A carregar...
Publicação
Nanofibrous Membranes Obtained by Electrospinning for Bone Tissue Engineering and Wound Dressing Applications
| Nome: | Descrição: | Tamanho: | Formato: | |
|---|---|---|---|---|
| 13.07 MB | Adobe PDF |
Autores
Orientador(es)
Resumo(s)
The current Doctoral Thesis work has been performed under a co-supervision agreement between University of Zaragoza (Home University), University of Calabria (Host University) and Faculty of Sciences and Technology of the NOVA University of Lisbon (FCT NOVA) (Host University). This research has been carried out inside the Erasmus Mundus Doctorate in Membrane Engineering program (EUDIME), (FPA 2011-0014), funded by the European Union.
This thesis focused mainly on the use of the electrospinning technique to produce different kind of membranes for biomedical applications. In particular, it described the synthesis and production of inorganic and organic nanoparticles to be used as fillers or as carriers (drug delivery system) as well as the production of electrospun nanofibrous membranes. This work was carried out within the Institute of Nanoscience of Aragon (INA), specifically in the Nanostructured Films and Particles (NFP) group under the supervision of the Professor Silvia Irusta and Dr Gracia Mendoza. Also an important part of the physico-chemical characterization was done at INA.
The study of different biological signals and the use of specific techniques for membrane characterization were acquired at the University of Calabria under the supervision of Dr. Loredana De Bartolo in the Institute on Membrane Technology of the National Research Council of Italy (ITM-CNR). On the other hand, the mobility carried out at the Faculty of Sciences and Technology (FCT NOVA) of Universidade NOVA (FCT NOVA) under the supervision of Professor Ana Isabel Aguiar-Ricardo, allowed a total characterization of two asymmetric membranes following different International Standards to accomplish testing for primary wound dressing.
The development of novel membranes loaded with morphogenetic proteins or antibiotic are of great interest in the field of bone tissue engineering. To promote the cellular viability and extracellular matrix production, electrospun membranes with enhanced porosity and micro-scale pores could be beneficial since increased porosity and pore size can provide a three-dimensional (3D) environment that not only facilitates cell seeding/diffusion but also provides better diffusion of nutrients and waste throughout the membranes. The addition of calcium phosphate ceramics has been extensively investigated to fabricate highly porous membranes to bone tissue engineering due to their close similar composition of bone, including excellent biocompatibility, osteoinductive and osteoconductive properties. A homogeneous distribution of the bone morphogenetic protein-loaded particles along the entire membrane could be ensuring a continuous release of the growth factor to provide the necessary biochemical cues for bone repair and regeneration.
Antibiotic-loaded membranes may provide drug targeted and sustained release, avoiding the long-term oral and intravenous systematic multidrug administration, which implies toxic side effects, low delivery to the target site and low patient adherence to the treatment. Therefore, membranes loaded with antibiotics can overcome the drawbacks of the traditional therapy sustaining enhanced osteogenic properties for the successful regeneration of the bone.
Another interesting biomedical application of electrospun membranes is the fabrication of efficient smart dressings for the treatment of wounds. A rapid wound healing requires developing appropriate membranes with interconnected pores that allow the oxygen diffusion and transport of metabolic waste, as well as an adequate pore size to prevent rapid dehydration and bacteria penetration. A high absorption capacity and adequate water vapor transmission will be necessary to keep a moist environment in the wound bed. Besides, if the electrospun membrane has some bactericidal properties will be better for the healing process.
The main goal of this thesis was the development of fibrous membranes by electrospinning with the appropriate characteristics to be used in bone tissue engineering or as wound dressing materials. To achieve this target, several specific objectives were defined, which are described in Chapters II to V.
Descrição
Prepared in the framework of Erasmus Mundus Doctorate in Membrane Engineering (EUDIME) to obtain multiple Doctoral degrees issue by
Universidad de Zaragoza, Departamento de Ingeniería Química y Tecnología del Medio Ambiente, Università della Calabria, Istituto per la Tecnologia delle Membrane (ITM), Universidade Nova de Lisboa, Facultade de Ciência e Tecnologia